To replace the pull cord on a leaf blower, you will need a few tools and follow these steps:
- Start by disconnecting the spark plug wire to prevent accidental starting. This is an important safety precaution.
- Remove any screws or clips that hold the recoil starter housing in place. Typically, these will be located on the top or side of the blower's engine. Use a screwdriver or socket wrench to loosen and remove them.
- Once the housing is loose, carefully lift it off to access the recoil starter assembly. Set the housing aside in a safe place.
- Inspect the old pull cord attached to the recoil starter assembly. If it has snapped or has become frayed, it needs to be replaced. Ensure you have a suitable replacement cord before proceeding.
- To remove the old cord, unwind it from the recoil starter pulley. Tug gently on the cord until all of it has come free from the pulley.
- Prepare the new pull cord by feeding one end through the hole or eyelet in the center of the recoil starter pulley. Tie a secure knot to prevent it from slipping back through.
- Once the cord is tied, wind it around the pulley securely in the direction indicated by any arrows or engraved instructions. Wind it tightly but avoid over-tightening, as it may prevent the cord from recoiling properly.
- After winding the pull cord, thread the loose end through the hole on the outer rim of the recoil starter housing.
- Reattach the recoil starter housing by aligning it properly with the blower's engine. Secure it in place using the screws or clips you removed earlier.
- Before using the leaf blower again, test the recoil starter by giving the cord a gentle tug. It should reel back into the housing smoothly. If it doesn't, recheck the cord's installation and winding on the pulley.
Remember to reconnect the spark plug wire before starting the leaf blower. Following these steps will help you replace the pull cord and ensure your leaf blower is in working condition.
Best Leaf Blowers and Vacuums of 2024
1
Rating is 4.9 out of 5
EGO Power+ LB6504 650 CFM Variable-Speed 56-Volt Lithium-ion Cordless Leaf Blower 5.0Ah Battery and Charger Included
-
Turbo button delivers 650 CFM, up to 180 MPH with tapered nozzle attached
-
Up to 90 minutes of average runtime on a single charge with the included 56V 5.0Ah ARC Lithium battery
-
Variable speed dial from 225 CFM to 470 CFM with lock on button for ultimate control
-
High-efficiency brushless motor
-
IPX4-rated weather-resistant construction
-
64 dB noise level
-
Compatible with all EGO 56V ARC Lithium batteries
-
Spread and tapered nozzle attachments included
-
5-year tool warranty, 3-year battery warranty
2
Rating is 4.8 out of 5
Husqvarna 970466901 150BT Gas Leaf Blower, 51-cc 2.16-HP 2-Cycle Backpack Leaf Blower, 765-CFM, 270-MPH, 22-N Powerful Clearing Performance
-
Husqvarna 150BT Gas Backpack Leaf Blower combines a high powered gas leaf blower with state-of-the-art ergonomic design, a perfect gift for dad
-
Powerful Clearing Performance: 2-cycle, 51-cc, 2.16-HP engine has a powerful blowing force (765 CFM, 270 MPH, 22 N), reduces emissions up to 60%, and increases fuel efficiency up to 20%
-
Ergonomic Harness System: Gas leaf blower backpack features a padded harness, hip belt and weight-leveling load management system for optimal comfort
-
Easy Operation: Air purge system removes air from the carburetor and fuel system for trouble-free starting, plus the variable speed throttle with cruise control allows for easy operation without the need to regulate the blower's speed
-
Gas Blowers for Lawn Care: Gas leaf blowers simplify the process of regular yard maintenance and more demanding lawn care tasks, like cleaning up heavy, wet leaves and debris
3
Rating is 4.7 out of 5
EGO Power+ LB5302 3-Speed Turbo 56-Volt 530 CFM Cordless Leaf Blower 2.5Ah Battery and Charger Included
-
Turbo button delivers 530 CFM, up to 110 MPH to power through heavy debris
-
Up to 75 minutes of runtime on a single charge with the included 56V 2.5Ah ARC Lithium battery
-
Variable speed dial from 260 CFM to 400 CFM with lock on button for ultimate control
-
High-efficiency brushless motor
-
IPX4-rated weather-resistant construction
-
64 dB noise level
-
Compatible with all EGO 56V ARC Lithium batteries
-
5-year tool warranty, 3-year battery warranty
4
Rating is 5 out of 5
Cordless Leaf Blower - Electric Leaf Blower Cordless with 2 Batteries and Charger - 2 Speed Mode - 21V Battery Powered Leaf Blowers for Lawn Care, Patio, Blowing Leaves and Snow
-
【Up to 2x Batteries】Tired of the time consuming of leaf raking and the back pain? Tired of the limitation of cord, the noise from the bulky blowers? Consider getting the LAZYBOI cordless leaf blower with two batteries for tackling your lightweight jobs. Within 30 mins, you can get your work done in any terrain, even for roofs and gutters.
-
【Faster Charging and No Hassles】 Sometimes customers got annoyed by waiting too long to charge the battery. But with the LAZYBOI leaf blower, you will get the convenience of 1-hour fast charging. The cordless leaf blower set comes with a fast charger and two 2.0ah 21v batteries which keeps 40-min work for the low speed mode and 30-min work for the high speed mode.
-
【Advanced Motor with Turbo Tech】LAZYBOI cordless leaf blower uses advanced turbo technology, which effectively boosts the maximum air speed to 150MPH. Although the turbo mode uses a lot of power (which drains the battery faster), it is quite useful for loosening up those stubborn patches of debris that get stuck and otherwise refuse to budge. Our LAZYBOI blower is absolutely a lightweight and cordless leaf blower that brings a better user experience than others'.
-
【Lightweight and Portable】 Lightweight design makes it perfect for one-handed operation for easy maneuverability. Weighs only 3.38 lbs and features an ergonomic body that naturally moulds to the direction of blowing, you will experience 30% less user fatigue during operation. The upgraded rubber grip of the leaf blower is not only non-slip when used, but also provides you with just enough support to make your work easier.
-
【Battery Maintenance】 Product Safety is Top 1 to consider, we've implemented overheat protection in our batteries to ensure consumer safety. To prolong battery life, please wait 5-10 minutes after discharge before charging, and fully charge the battery before storing it for 3+ months. The LED indicator shows red while charging and green when fully charged.
-
【12 Month Waranti】 We offer you 12 months of free warranti service to make your leaf blower more durable and reliable. If you have any problems with our cordless leaf blower, please feel free to contact us, and we will answer it within 24 hours.
5
Rating is 4.6 out of 5
DEWALT 20V MAX* XR Leaf Blower, Cordless, Handheld, 125-MPH, 450-CFM, Tool Only (DCBL722B)
-
Up to 450 CFM of air volume and up to 125 Mph with concentrator
-
Innovative axial fan design that maximizes on air output and run time
-
Low noise during operation - 66 dB(A), ideal for noise sensitive regions and properties
-
High-efficiency brushless motor helps extend run time and motor life
-
Lightweight and ergonomic design allows for easy control and arm movement
6
Rating is 4.5 out of 5
VacLife Leaf Blower Cordless with Battery and Charger-350CFM 150MPH 20V Electric Leaf Blower, Perfect for Lawn, Yard, Garage, Patio & Sidewalk Red (VL717)
-
POWERFUL MOTOR & EFFICIENT CLEANING: VacLife cordless leaf blower is equipped with a copper motor which makes the appliance durable, energy-saving, and less noisy. In addition, the turbo booster helps to provide stronger airflow, which is up to 280 CFM. Plus the strong wind speeds up to 120 MPH, VacLife can work efficiently in helping you clean the target area.
-
CORDLESS DESIGN & LONG BATTERY LIFE: This battery powered leaf blower is cordless and portable. It's convenient for you to carry around. The 20V 4.0Ah battery can support the blower to work for 25 mins in high-speed mode and 15 mins in turbo-speed mode. What's more, it only takes 2h to fully charge the battery. You can monitor the remaining battery and charging process by the indicators.
-
VARIABLE SPEEDS: This cordless leaf blower features variable speeds. The harder you press the power switch, the stronger the wind is. By pressing the turbo-speed button at the same time, the wind reaches its strongest speed. Thus, this blower can not only blow away leaves, fragments, and dust but also snow and stubborn debris. You can choose suitable speeds freely to solve your problems.
-
WIDE-APPLICATION: This electric blower is suitable for many different uses. It is not limited to the function of a lawn vacuum or a yard vacuum. It can be used to clean the garage, patio, sidewalk, porch, car, balcony, deck, and hard-to-reach areas. Moreover, this electric blower works effectively in cleaning damp leaves, snow, dust, and fragments as well as drying your car surface.
-
USER-FRIENDLY & ERGONOMIC DESIGN: The handgrip of this blower for lawn care is wrapped with elastic rubber which makes it non-slip and comfortable to hold. Meanwhile, the assembly of the appliance can be finished easily in a few steps by referring to the user manual included in the package. ( Note: Please read the manual carefully before using the electric blower. )
7
Rating is 4.4 out of 5
Toro 51621 UltraPlus Leaf Blower Vacuum, Variable-Speed (up to 250 mph) with Metal Impeller, 12 amp,Red
-
Superior blowing and mulching proven by controlled laboratory testing.This bag is designed to capture leaf particles not dust. Product needs air flow to work properly.3 in 1 Machine - Powerful Blower, High Speed Vacuum, Leaf Shredder340 CFM blow mode and 405 CFM Vac mode3 in 1 Machine - Powerful Blower, High Speed Vacuum, Leaf Shredder
-
Powerful up to 250 mph degree. 350 CFM blow mode and 410 CFM Vac mode
-
Vacuum tube, bottom-zip bag, cord storage hook, shred-all shred ring and time-saving oscillating tube included; Extension cord Sold separately
-
Variable speed control for better control in both blower and vac mode
-
This bag is designed to capture leaf particles not dust. Product needs air flow to work properly.
-
3 in 1 Machine - Powerful Blower, High Speed Vacuum, Leaf Shredder
-
340 CFM blow mode and 405 CFM Vac mode
-
3 in 1 Machine - Powerful Blower, High Speed Vacuum, Leaf Shredder
8
Rating is 4.3 out of 5
WORX WG520 12 Amp TURBINE 600 Electric Leaf Blower
-
[TURBINE FAN TECH] Worx engineers figured out how to get a jet engine-type motor inside of a leaf blower. Super powerful, yet not so loud that you’ll think it’s getting ready for takeoff
-
[TWICE AS FAST AS PRO BLOWERS] Professional-grade gas blowers rely on outdated tech. The Turbine is cutting edge, and spins twice as fast as the blowers used by commercial grounds crews
-
[2 SPEEDS FOR DIFFERENT JOBS] Go slow for pavement or tight corners. On the open lawn, switch to speed 2 and see what the 110 mph Turbine can do
-
[600 CFM] We named the Turbine 600 after the 600 Cubic Feet per Minute of high-capacity air volume that shoots out of its wide-mouth nozzle. That’s a wide, strong path of air that allows you to clear large areas with fewer passes
-
[DO IT YOURSELF. DO IT BETTER. DO IT WITH WORX.] WORX tools are engineered with cutting-edge technology, and above modern efficiency standards, so you can build a cost-effective tool collection that’s been designed to last
-
[HYPER-STREAM AIR NOZZLE] We didn’t just stop designing once we were finished with the Turbine engine. We added an attachable nozzle, optimized to direct all that volume in a concentrated area for tougher jobs
-
[ONE-HANDED OPERATION] All the power and only 6.4 lbs. The Turbine 600 is designed to be controlled with just one hand. The ergonomic design funnels the wind in a way that’s easy to handle
-
[EXTENSION CORD RETAINER] The electrical cord comes with a retainer attached, so when using an extension cord it won’t disconnect, even when it gets snagged
What is the estimated time required to replace a leaf blower's pull cord?
The estimated time required to replace a leaf blower's pull cord can vary depending on several factors such as the model of the leaf blower, the experience of the person doing the replacement, and the tools available. However, on average, it may take around 30 minutes to 1 hour to replace a leaf blower's pull cord.
What are the signs that indicate a worn-out pull cord on a leaf blower?
There are several signs that may indicate a worn-out pull cord on a leaf blower:
- Difficulty in pulling the cord: If you find it increasingly challenging or strenuous to pull the cord, it might be a sign that the cord is worn out. A worn-out pull cord can become frayed or lose its elasticity over time, making it more difficult to pull and start the leaf blower.
- Cord snapping back inside: If the cord snaps back inside the leaf blower housing after being pulled, it could mean that the cord has become detached or worn out. This can happen when the cord loses its grip or has become tangled, preventing it from fully extending and retracting.
- Visible fraying or damage: Inspect the pull cord for any signs of fraying, breakage, or damage. Over time, the cord can become damaged due to repeated use, exposure to weather conditions, or other factors. If you notice any visible signs of wear, it is likely that the pull cord needs to be replaced.
- No resistance or tension: When you pull the cord, it should provide resistance and tension. If you find that the cord easily pulls out without any resistance or tension, it could indicate a worn-out or broken pull cord. This can make it impossible to start the leaf blower.
- Lack of recoil: If the pull cord does not recoil or retract fully after being pulled, it suggests that the cord or its recoil mechanism may be worn out. This can make it difficult to start the leaf blower as the cord does not fully reset for the next pull.
If you observe any of these signs, it is advisable to replace the worn-out pull cord to ensure proper functioning of the leaf blower.
How to lubricate the pull cord assembly on a leaf blower?
To lubricate the pull cord assembly on a leaf blower, follow these steps:
- Start by disconnecting the spark plug wire to ensure the engine doesn't accidentally start during the lubrication process.
- Locate the pull cord assembly on the leaf blower. It is usually located at the top or side of the engine and may be covered by a protective plastic or metal housing.
- Remove any covering or housing that is obstructing access to the pull cord assembly. This may require using a screwdriver or wrench to loosen and remove screws or bolts.
- Once you have exposed the pull cord assembly, inspect it for any signs of dirt, debris, or damage. Clean or replace any damaged components as necessary.
- Apply a small amount of lubricating oil or silicone spray to the moving parts of the pull cord assembly, including the pulley and any other areas where friction is present. Be sure not to over-lubricate, as excessive lubrication can attract dust and dirt, leading to further issues.
- Gently pull the cord a few times to distribute the lubricant and ensure smooth operation.
- Reassemble any covers or housing that were removed during the process, and secure them in place with screws or bolts.
- Reconnect the spark plug wire.
- Test the pull cord assembly by giving it a few firm pulls to ensure it is working smoothly and without any issues.
It's important to note that it's best to consult your leaf blower's manual for specific instructions on lubricating the pull cord assembly, as different models may have different requirements or recommendations.
What is the purpose of the pawl in a leaf blower's pull cord mechanism?
The pawl in a leaf blower's pull cord mechanism serves the purpose of engaging and disengaging the engine's starter mechanism. When the pull cord is initially pulled, the pawl engages with the starter mechanism, allowing it to rotate and start the engine. Once the engine is running, the pawl disengages from the starter mechanism, preventing it from rotating and avoiding any potential damage. Essentially, the pawl is responsible for controlling the movement of the starter mechanism based on the position of the pull cord.
How to remove the pull cord on a leaf blower?
The process to remove the pull cord on a leaf blower may vary depending on the specific model and make of your leaf blower. However, here are general steps that you can follow:
- Ensure safety: Disconnect the spark plug wire from the spark plug to prevent accidental starting.
- Access the housing: Locate the pull cord housing, which is usually located on top of the leaf blower. You may need to remove some screws or protective covers to access the housing.
- Remove the cord: Once the housing is accessible, you will find a spool or reel with the pull cord wound around it. Carefully unwind the cord from the spool, taking note of the way it is wound.
- Remove the handle: Most pull cords have a handle on one end. Find the knot securing the handle and carefully remove or untie it.
- Replace or repair: If you are simply replacing the pull cord, you can untie or cut the cord near the spool, remove it completely, and replace it with a new cord by following the steps in reverse order. If you are repairing the existing cord, untangle or fix any knots or snags, and wind the repaired cord back onto the spool.
- Reassemble: Once the new cord is in place or the existing one is repaired, wind it evenly around the spool. Make sure the spool is properly seated in its housing, then reattach any covers or screws you had removed.
- Reconnect spark plug wire: Reconnect the spark plug wire to its spark plug.
Note: It is recommended to consult the owner's manual of your specific leaf blower model for detailed instructions on disassembling and reassembling the pull cord, as specific steps may vary.
