Skip to main content
ponddoc.com

Back to all posts

How to Replace the Brush Roll on A Shark Vacuum?

Published on
5 min read

Table of Contents

Show more
How to Replace the Brush Roll on A Shark Vacuum? image

To replace the brush roll on a Shark vacuum, you will need to follow these steps:

  1. Turn off and unplug the vacuum: Ensure that the vacuum cleaner is switched off and unplugged from the power source to prevent any accidents.
  2. Locate the brush roll cover: Flip the Shark vacuum cleaner over and look for the brush roll cover. It is usually located on the bottom of the vacuum head.
  3. Remove the brush roll cover: Depending on the specific Shark model, there may be clips, screws, or latches holding the brush roll cover in place. Gently release or unscrew them to remove the cover and access the brush roll.
  4. Take out the old brush roll: Slide the old brush roll out of its housing. It may be necessary to apply slight pressure to dislodge it. Make sure to examine the brush roll for any wear or damage.
  5. Insert the new brush roll: Take the new brush roll and align it properly with the housing. Apply gentle pressure to secure it in place. Ensure that the brush roll is positioned correctly and rotates freely.
  6. Reattach the brush roll cover: Place the brush roll cover back over the brush roll housing. Fasten it securely using the clips, screws, or latches you released earlier.
  7. Test the vacuum cleaner: Once the brush roll cover is securely attached, flip the vacuum cleaner back to its original position. Plug the vacuum in and turn it on to check if the new brush roll is functioning properly.

Remember to consult your Shark vacuum's user manual for any specific instructions or troubleshooting tips.

What is the average lifespan of a Shark vacuum's brush roll?

The average lifespan of a Shark vacuum's brush roll can vary depending on several factors such as the frequency of use, the type of flooring it is used on, and how well it is maintained. However, on average, a well-maintained Shark vacuum brush roll can last anywhere from 6 months to 2 years before it may need to be replaced.

How to clean a Shark vacuum?

To clean a Shark vacuum, follow these steps:

  1. Unplug the vacuum: Before you begin any cleaning, make sure the vacuum is unplugged from the power source.
  2. Empty the dust cup: Locate the dust cup, which is usually located at the bottom of the vacuum. Press the release button, if applicable, and remove the dust cup from the vacuum. Empty the contents into a trash bag or bin.
  3. Clean the dust cup: Rinse the dust cup with warm, soapy water. Use a brush or sponge to scrub away any dirt or debris stuck inside. Rinse thoroughly and let it air dry completely before reattaching it to the vacuum.
  4. Remove and clean the filters: Sharks vacuums typically have two filters - a foam filter and a felt filter. Refer to your vacuum's user manual to locate and remove the filters. Rinse them under warm water, gently squeezing and rinsing until the water runs clear. Do not use any soap or cleaning agents on the filters.
  5. Let the filters dry: After rinsing, shake off any excess water from the filters and place them in a well-ventilated area to air dry. Ensure they are completely dry before reinserting them into the vacuum.
  6. Clean the brush roll: Flip the vacuum over to access the brush roll, which is the rotating brush located at the base of the vacuum head. Remove any tangled hair, threads, or debris from the brush roll using scissors, a seam ripper, or your fingers. Use a damp cloth or brush to wipe away any remaining dirt or grime.
  7. Check the hoses and attachments: Inspect and clean any hoses or attachments that may be clogged or dirty. Detach these parts, as per your vacuum's design, and use a brush or cloth to remove any debris. Rinse them if necessary, but make sure they are dry before reattaching them.
  8. Reassemble the vacuum: Once all the parts are cleaned and thoroughly dried, reattach the dust cup, filters, brush roll, hoses, and attachments to the vacuum. Ensure they are securely in place.
  9. Wipe down the exterior: Use a damp cloth to wipe down the exterior of the vacuum, removing any dust or smudges.
  10. Store the vacuum properly: Finally, store your cleaned Shark vacuum in a cool, dry place, ready for your next cleaning session.

Remember to consult your vacuum's user manual for model-specific instructions and precautions before cleaning.

How to clean the brush roll of a Shark vacuum?

To clean the brush roll of a Shark vacuum, follow these steps:

  1. Turn off and unplug the vacuum.
  2. Locate the brush roll cover on the bottom of the vacuum head. It is usually secured with two screws. Use a screwdriver to remove the screws and take off the cover.
  3. Remove any hair, threads, or debris wrapped around the brush roll. You can use scissors or a seam ripper to carefully cut and remove any tangled or wrapped items. Be cautious not to damage the brush roll bristles.
  4. Use a clean, damp cloth or sponge to wipe down the brush roll and remove any remaining dirt or debris.
  5. Inspect the end caps of the brush roll for any build-up or blockages. If you notice any, use a toothbrush or small brush to carefully clean them.
  6. After cleaning the brush roll and end caps, reattach the brush roll cover and secure it with the screws.
  7. Plug in the vacuum and turn it on to ensure the brush roll is spinning smoothly.

It is recommended to clean the brush roll regularly, at least once every month or as needed, to maintain optimal vacuum performance.